Franklin Hodge Industries storage tank - Products(2)

Galvanized Liquitainer
Where space is at a premium, the Liquitainer ® / Firetainer ® tank is an ideal solution for bulk water storage indoors or out. A wide range of shapes and any length or width can be catered for, with a maximum height of 4.5m.
Using steel sections of either rectangular, circular or u-beams, a structure is formed which eliminates the need for internal bracing. Galvanised steel panels are bolted between the sections and the interior is fitted with an open top tailored membrane liner. Alternative covers are available either fl at with a raised ball valve housing for indoor use, or with a low profile pitch for outdoor use.
Liquitainer ®/ Firetainer ® tanks can be located on any suitable flat load bearing surface, such as an existing reinforced concrete floor, or roof top, and are simply bolted to the floor surface.
Firetainer ® tanks are approved by the UK Loss Prevention Certification Board for the storage of fire sprinkler water.

Versatility in design. A variety of shapes and sizes can be supplied. Existing obstructions such as building support columns can be encapsulated within the tank by ‘sleeving’ the membrane liner around them.
Ease and speed of assembly. No sealants are used in the construction of the tank. All that is required is straightforward site assembly.
Simplicity of foundations. There is no need to seal the tank to the concrete foundation. The membrane liner has a floor in it and the tank shell is simply bolted to the foundation.
Low maintenance. The outer steelwork structure is hot dip galvanised to BS EN ISO 1461 (1999) and the shell panels and connection plates are manufactured from pre-galvanised steel sheet coated with a heavy duty spangle finish, complying to BS EN 10147 Grade Fe E280G. Internally the membrane liner will not rot or degrade in the same way that other coatings and finishes do, under normal water storage conditions.

Galvanised Tritainer

For small to medium capacities of water storage, where space is at a premium, the Tritainer ®/ Firetainer ® tank offers a cost effective solution.
Using triangular shaped galvanised steel panels which make up 1.0m2 modules that are then bolted together on site, a rapidly assembled rectangular tank that can fit into small and difficult spaces can be provided. Internally a hot vulcanised tailor made membrane liner is fitted to the tank. Any length and width can be catered for, with a maximum height of 2.5m.
Firetainer ® tanks are approved by the UK Loss Prevention Certification Board for the storage of fire sprinkler water.

- Easy to handle, relatively small panels, enabling easy access to restricted areas.
- No internal bracing. This means no internal corrosion problems.
- No sealants or gaskets to the tank shell, which means faster installation and elimination of

leakage problems.
- Insulation can be placed internally between the tank liner and tank wall, thereby protecting

the insulation from the environment and vandalism.

Aluminium Liquitainer

Where space is at a premium, the Liquitainer ®/ Firetainer ® tank is an ideal solution for bulk water storage indoors or out. A wide range of shapes and any length or width can be catered for, with a maximum height of 5.4m.
Using steel sections of either rectangular, circular or u-beams, a structure is formed which eliminates the need for internal bracing. Aluminium panels are bolted between the sections and the interior is fi tted with an open top tailored membrane liner. Alternative covers are available either flat with a raised ball valve housing for indoor use, or with a low profile pitch for outdoor use.
Liquitainer ®/ Firetainer ® tanks can be located on any suitable flat load bearing surface, such as an existing reinforced concrete floor, or roof top, and are simply bolted to the floor surface.
Firetainer ® tanks are approved by the UK Loss Prevention Certification Board for the storage of fi re sprinkler water.

Versatility in design.

A variety of shapes and sizes can be supplied. Existing obstructions such as building support columns can be encapsulated within the tank by ‘sleeving’ the membrane liner around them.
Ease and speed of assembly.

No sealants are used in the construction of the tank. All that is required is straightforward site assembly.
Simplicity of foundations.

There is no need to seal the tank to the concrete foundation. The membrane liner has a fl oor in it and the tank shell is simply bolted to the foundation.
Low maintenance.

The outer steelwork structure is hot dip galvanised to BS EN ISO 1461 (1999) and the aluminium shell panels are of a marine grade aluminium alloy to BS EN AW 5083 H22. Internally the membrane liner will not rot or degrade in the same way that other coatings and fi nishes do, under normal water storage conditions.

Franklin Hodge Industries storage tank - Products

Galvanized Liquistore

For standard fire sprinkler water storage applications or general industrial water storage requirements, the Liquistore ® / Firestore ® tank is a cost effective solution.
Using site assembled components, consisting of overlapped and bolted galvanised steel panels with either a trough deck or aluminium sectional site assembled cover, together with an internal, open top membrane liner, the Liquistore ® / Firestore ® offers a truly long life and low maintenance water storage system.
Standard tanks are available in capacities from 10m3 (2,200 UK gallons) to 2,222m3 (488,840 UK gallons) and in diameters from 3.06m to 21.40m and heights from 1.25m to 13.26m. Non standard and larger size tanks are available upon request.
Firestore ® tanks are approved by the UK Loss Prevention Certification Board and Factory Mutual Assurance of the United States of America for storage of fire sprinkler water and by the UK Water Regulations Advisory Scheme for the storage of potable water under the name Liquistore®.

Ease and speed of assembly. No sealants are used on the tank shell. This means that site installation can make full use of hydraulic jacking with the confi dence in knowing that the integrity of the tank is not reliant on a large number of individual panel seals. Simplicity of foundations. All that is required to site the tank
Simplicity of foundations. All that is required to site the tank is a fl at load bearing surface, typically of reinforced concrete. The bottom rolled angle at the tank base is simply bolted to the concrete floor.
Low maintenance. The galvanised steel panels to the tank are made from high quality pre-galvanised strip to BS2989 Grade Z35, with a zinc coating of 300g/m2 each side of the panel. For plate thicknesses above 4.2mm, each plate is hot dip galvanised to the requirements of BS EN ISO 1461 (1999). This means a highly corrosion resistant exterior fi nish to the tank. Internally the hot vulcanised, tailor-made membrane liner separates the stored water from the tank shell, often a major cause of corrosion. The membrane liner itself will not rot or deteriorate in the same way that other coatings and fi nishes to the interior of tanks will.

Aluminum Liquistore

The tank is of cylindrical bolted construction, made from EN 48S-2 Type EN AW 5083- H22 aluminium alloy with aluminium angle strengthening hoops of Grade 6082-T4 at the top and bottom, and is supplied with an aluminium low profile sectional cover incorporating a ball valve housing and access way.
Liquid Storage Containers. Click image to enlarge
A typical aluminium Liquistore® installation of three 155,100 gallon tanks (non-standard ladder arrangement).Rapid and straightforward to install.Virtually zero maintenance internally and externally.Long life.Easy to transport, ideal for remote areas.Prefabricated components for site assembly.
In addition the tank is fitted with an open top internal membrane liner. The assembled tank is clamped down with anchor bolts fixed to the base.
All tanks are normally supplied complete with external aluminium hooped access ladder (beginning approximately 2.4m from tank base), aluminium handrailing around the access platform, calibrated contents gauge, 25mm warning overflow, 80mm drain valve and other connections as required.
Standard tanks are available in capacities from 20m3 (4,400 UK gallons) to over 5000m3 (1,100,000 UK gallons), diameters from 3.06m to 32.17m and heights from 2.477m to 13.26m. Tanks can be supplied on a specially designed steel support structure at any specified height above ground level. Non-standard and larger sizes in other tank materials and cover types can be built to suit particular applications.
Our standard Liquistore ® is designed to withstand normal UK conditions when fully complete and filled. Non-standard designs are available to meet particular criteria. Fully complete but unfilled, the standard Liquistore ® will normally withstand moderate wind loadings. Actual performance will depend upon tank configuration and diameter to height ratio. Where a Liquistore ® is expected to be subject to particularly severe conditions, or to be regularly in the unfilled condition, additional strengthening will be provided.

- Rapid and straightforward to install.
- Virtually zero maintenance internally and externally.
- Long life.
- Easy to transport, ideal for remote areas.
- Prefabricated components for site assembly

Franklin Hodge Industries storage tank

CYLINDRICAL STORAGE TANKS

Our Firestore/Liquistore range of cylindrical tanks are our most popular. Using flat sheets of high grade, high zinc galvanised steel, or a “marine grade” alloy of aluminium, Firestore / Liquistore tanks are bolted together on site with a tailor made internal liner to contain the stored water.

Galvanised Liquistore ® / Firestore ®

For standard fire sprinkler water storage applications or general industrial water storage requirements, the Liquistore ® / Firestore ® tank is a cost effective solution.

Aluminium Liquistore ® / Firestore ®

The tank is of cylindrical bolted construction, made from EN 48S-2 Type EN AW 5083- H22 aluminium alloy with aluminium angle strengthening hoops of Grade 6082-T4 at the top and bottom, and is supplied with an aluminium low profile sectional cover incorporating a ball valve housing and access way.


RECTANGULAR STORAGE TANKS

Our Firetainer/Liquitainer range of rectangular tanks offer a very effective method of making use of limited space for the storage of water. Either flat or triangular sheets of a high grade, high zinc galvanised steel, or a marine grade alloy of aluminium, bolted to galvanised steel stanchions or stiffeners, can be used to design a wide range of tank shapes and sizes to suit awkward spaces.

Galvanised Liquitainer ® / Firetainer ®

Where space is at a premium, the Liquitainer ® / Firetainer ® tank is an ideal solution for bulk water storage indoors or out. A wide range of shapes and any length or width can be catered for, with a maximum height of 4.5m.

Galvanised Tritainer ® / Firetainer ®


For small to medium capacities of water storage, where space is at a premium, the Tritainer ® / Firetainer ® tank offers a cost effective solution.


Aluminium Liquitainer ® / Firetainer ®


Where space is at a premium, the Liquitainer ® / Firetainer ® tank is an ideal solution for bulk water storage indoors or out. A wide range of shapes and any length or width can be catered for, with a maximum height of 5.4m.

Franklin Hodge Industries

Welcome

Franklin Hodge Industries welcomes you to the world of reliable and proven site-assembled liquid storage tanks. Our water storage tanks are installed on every continent and in virtually every climatic condition. Franklin Hodge is proud of it’s postion as a recognised standard for quality in the tank industry.

What We Do

Franklin Hodge Industries design, manufacture and install a range of cylindrical and rectangular water storage tanks.

Why Buy Franklin Hodge Tanks?

Franklin Hodge Industries liquid storage tanks and products offer customers the following benefits:
A proven track record.
Confidence, reliability and peace of mind.
Design flexibility and solutions to problems.
Support of an experienced and professional team.
Over thirty years experience within the tank industry.
Team-work from quotation to commission.

WRAS Approved Water Fittings:Section 0225

WRAS Approved Water Fittings

Section 0225
Cisterns FIRE SPRINKLER SUCTION

Listing Number 0504078

`DECCA` Firestor range of GRP sectional hot press moulded sectional cold-water storage cisterns, for fire sprinkler systems with uPVC roof panels. Cisterns are constructed from metric panels, (2m x 1m, 1.5m x 1m, 1m x 0.5m and corner sections, or 1.2m x 1.2m, 1.2m x 0.6m and corner sections). Panels can be supplied pre-insulated and are assembled with extruded butyl rubber seals. Cistern can be internally braced with horizontal galvanised steel sections or alternatively cisterns can be braced with no internal tie rod systems. For non-potable water use.
Size: Maximum height 4m, maximum capacity 2,190,000 litres.
Product Designation: DECCA firestor/Flosto range.
Marking: 'DECCA Plastics', company contact details and WRAS logo printed on adhesive label on body.
Installation Requirements : R001 R270 R350

Note:
Proviso:
Manufacturer: Decca Plastics Ltd

Listing Number 0304091

`1000 Module` range of hot pressed GRP sectional storage cisterns for the storage of water for fire sprinkler systems, incorporating a screened Type `AB` air gap arrangement. The panels are sealed using Butyl Rubber sealing tape. Units can be supplied with additional access hatches for the inspection of the air gap arrangement. 50mm valve, weir length = 800, weir depth = 127. Value of `h` = 27 & air gap = 100mm (2 x dia). 80mm valve, weir length = 800, weir depth = 196. Value of `h` = 46 & air gap = 150mm (2 x dia). 100mm valve, weir length = 1600, weir depth = 243. Value of `h` = 43 & air gap = 200mm (2 x dia). 150mm valve, weir length = 2400, weir depth = 356. Value of `h` = 56 & air gap = 300mm (2 x dia).
Size: Panel size 1m², height 3m, capacity 576000 litres.
Product Designation: 1000 Module.
Marking: Cistern housing has data plated inscribed works order number, capacity, LPC number, BS7491 Part 3 1994, date and manufacturers details.
Installation Requirements : R001 R270 R280 R350

Note:
Proviso:
Manufacturer: Dewey Waters & Co Ltd
List all fittings by this manufacturer
Factor:

Listing Number 0412063

`Firestore` range of cylindrical sectional sprinkler suction tanks, constructed on a concrete base using BS EN 10147 Grade Fe350G pre-galvanised to a G600 heavy duty spangle finish sheets. Bolted together using spun galvanised nuts and bolts. The tank is stiffened top and bottom with a galvanised steel rolled angle. A tailor made Butyl liner is fitted inside the tank (Grade 72601). Covers may be plastic coated profiled sheet cladding or a galvanised steel support structure or alternatively aluminium alloy cladding on an aluminium structure. A float operated valve is provided with an access panel. The cisterns are fitted with Peter Smith float operated valves. The weir is provided with a 0.65mm square screen and a light box on the exterior of the tank.
Size: Maximum size 1211m3.
Product Designation: Firestore range.
Marking: Name plate stating Firestore, capacity, date installed, manufacturer`s name and address.
Installation Requirements : R001 R280

Note:
Proviso:
Manufacturer: Franklin Hodge Industries Ltd


Listing Number 0412060

`Firetainer` range of rectangular modular fire sprinkler suction tanks constructed on a concrete base. Either aluminium or galvanised steel panels on BS EN 10147 Grade F2350G pre- galvanised to a G600 heavy duty spangle finish, sheets bolted together using spun galvanised nuts and bolts. A tailor made butyl liner is fitted inside the tank (Grade 72601). Covers may be plastic coated profile sheet cladding on a galvanised steel support structure or alternatively aluminium profile sheeting on an aluminium structure. The units are supplied with Peter Smith float operated valves. The weir is provided with a 0.65mm square screen and a light box on the exterior of the tank.
Size: 1260m³.
Product Designation: Firetainer.
Marking: Name plate stating Firetainer, capacity, date installed, manufacturer`s name and address.
Installation Requirements : R001 R280

Note:
Proviso:
Manufacturer: Franklin Hodge Industries Ltd

Listing Number 0310065

`Sekisui` insulated or uninsulated storage cistern with AB air gap` the sectional comprises a cold water cistern assembled from glass reinforced plastics (GRP) panels and polyester resin for construction of cold water storage cisterns for wholesome water. The panels are constructed in sandwich form with a layer of GRP each side of a 20mm thick block of insulation (ridge polyethylene foam). Manufacturers calculated thermal capacity of the insulated panels is 0.022098. The largest capacity cisterns have stainless steel internal bracing and PVC pole supports. The roof covers are of the same panel construction provided with manhole inspection hatch, joints are sealed with synthetic rubber gaskets. The weir dimensions is relevant to the inlet size. The dimensions of the weir is 1m x 0.5m and is acceptable for use with inlet dimensions up to DN 80. The storage cistern must be installed with a WRAS approved electrically operated level control switch and a WRAS approved electrically operated inlet valve.
Size: Maximum height 4m maximum capacity 2270000 litres.
Product Designation: Sekisui Insulation Tank with AB air gap. FS (1 metre high). FH & FHX (1.5 metre high). FW, FJX & FWX (2 metre high). FT & FTX (2.5 metre high). FZ & FZX (3 metre high). FK & FKX (3.5 metre high). FQ & FQX (4 metre high).
Marking: Data plate on side of cistern showing model number, size, capacity manufactured date, nominal capacity and manufactures name and address.
Installation Requirements : R001 R270 R280 R350

Note:
Proviso:
Manufacturer: Sekisui Aqua Systems Co Ltd

WRAS Approved Water Fittings:Section 0170

WRAS Approved Water Fittings

Section 0170
Cisterns FEED AND EXPANSION - PLASTICS
Cisterns in this section are not suitable for water for domestic purposes unless they are so modified and installed as to comply in all respects with Schedule 2. Section 7, Paragraph 4. of the Water Supply (Water Fittings) Regulations 1999.

Listing Number 0209093

Rectangular cold water, feed and expansion cistern with close fitting lid. Supplied with front operated valve (BS1212 Part 2, Beta Ballvalve).
Size: 18 litre.
Product Designation: F & E Cistern - `Titan`.
Marking: Bottom of cistern moulded with product type.
Installation Requirements : R001 R130 R270 R350

Note:
Proviso:
Manufacturer: Gledhill Water Storage Ltd
List all fittings by this manufacturer
Factor:

Listing Number 0302055

`EX 104` range of rectangular black plastics (polypropylene Type B) feed and expansion cistern supplied with a backing plate of galvanised steel.
Size: 18 litres.
Product Designation: EX 104.
Marking: Cistern (top) moulded name of manufacturer, type, reference and capacity.
Installation Requirements : R130 R270 R280

Note:
Proviso:
Manufacturer: Polypipe Building Products Ltd

WRAS Approved Water Fittings:Section 0140

WRAS Approved Water Fittings

Section 0140

Cisterns COLD WATER STORAGE AND LIDS - METAL
Cisterns in this section are not suitable for water for domestic purposes unless they are so modified and installed as to comply in all respects with Schedule 2. Section 7, Paragraph 4. of the Water Supply (Water Fittings) Regulations 1999.
Listing Number 0212087


`Braithwaite` range of rectangular, sectional cold water storage cisterns for potable water, constructed from externally or internally bolted to BS 1564 Type 1, hot pressed steel panels with strip rubber and extruded mastic strip sealant. Panels may be galvanised to BS EN ISO 1461:1999, or shot blasted to SA2½ and primed with International Interplate 170. Following installation tanks may be coated with WRc or DWI approved coatings.
Size: 1,634,260 L (1634.26m³).
Product Designation: `Braithwaite` sectional storage cistern.
Marking: Panel pressed with manufacturers registered trademark.
Installation Requirements : R001 R270 R280 R320 R330

Note:
Proviso:
Manufacturer: Braithwaite Engineers Ltd
List all fittings by this manufacturer
Factor:

Listing Number 0306098


Range of sectional cold-water storage cisterns having a maximum depth of 3 x 4 ft panels (3.66m) supplied with a flat steel (for indoor installation) or pitched roof. Assembled from bolted pressed steel flanged panels 4ft (1.22m) x 4ft (1.22m) or (1m x 1m square) jointed with rubber sealing strips. Units are supplied with manholes and/or ventilator cowls with rubber gaskets. Cisterns are coated internally with a suitable approved paint.
Size: 522.964.
Product Designation: BSI 564 Type 1.
Marking: Data plate on side of tank printed company name, size and capacity, site name. Panels marked HB.
Installation Requirements : R270 R280 R320

Note:
Proviso:
Manufacturer: Horseley Bridge Tanks

WRAS Approved Water Fittings:Section 0130

WRAS Approved Water Fittings

Section 0130
Cisterns / COLD WATER STORAGE AND LIDS - PLASTICS

Cisterns in this section are not suitable for water for domestic purposes unless they are so modified and installed as to comply in all respects with Schedule 2. Section 7, Paragraph 4. of the Water Supply (Water Fittings) Regulations 1999.

Listing Number 0312117

Print this entry
`AQ` range of rectangular moulded pre-insulated (GRP) storage cisterns with bolted down lids (sealed with self-adhesive polyethylene foam). The internal surface of the storage cisterns is coated with a listed gelcoat. The cisterns are fitted with a screened air inlet, screened warning pipe and screened overflow (if over 1000 litres).
Size: 42 - 9000 litres.
Product Designation: `AQ` range.
Marking: Top of cistern with adhesive label showing company name, telephone number and capacity.
Installation Requirements : R001 R130 R270 R280 R350

Note:
Proviso:
Manufacturer: Aquatanks Ltd
List all fittings by this manufacturer
Factor:
List all fittings by this factor
Listing Number 0706066

Print this entry
`BOP` range of rectangular GRP storage cisterns manufactured from polyester resin. The lid is screwed into position and sealed with polyethylene foam.
Size: 240 litres - 4550 litres (50 gallons - 1000 gallons).
Product Designation: BOP50, BOP70, BOP70LP, BOP100, BOP100LP, BOP110LP, BOP125, BOP150, BOP200, BOP220, BOP220LP, BOP250, BOP300, BOP350, BOP400, BOP500, BOP500LP, BOP600, BOP800, BOP1000.LP denotes alternative low profile cisterns.
Marking: Manufacturer`s name, logo, capacity, model and date of manufacture printed on adhesive label attached to body.
Installation Requirements : R001 R130 R270 R280

Note:
Proviso:
Manufacturer: Balmoral Group Ltd
List all fittings by this manufacturer
Factor:
List all fittings by this factor
Listing Number 0503112

Print this entry
`Decca One Piece` range of GRP one-piece cold water storage cisterns and covers. Tanks are manufactured from glass-reinforced plastic and covers are sealed with WRAS approved polyethylene/butyl seal. The cisterns are supplied with screened air inlet and above 1000 litres an inspection hatch is provided. The cisterns are supplied either un-insulated or pre- insulated. For a full product range see manufacturer`s catalogue.
Size: DP10-DP26, M1-M16, CM01-CM24, TP10-TP26.
Product Designation: Decca One Piece, Decca Two Piece.
Marking: Adhesive label with Decca Plastics, address, model and trade name and certification number.
Installation Requirements : R001 R270 R280

Note:
Proviso:
Manufacturer: Decca Plastics Ltd
List all fittings by this manufacturer
Factor:
List all fittings by this factor
Listing Number 0507098

Print this entry
Range of one-piece GRP cold-water storage cisterns and lids. Units can be pre-insulated with polyurethane foam or standard non-insulated manufacture. Capacity range 30L - 4500L.
Size: 30 litres - 4500 litres.
Product Designation: A, B, C, D, E, F, G and H ranges.
Marking: Adhesive label with Dewey Waters, capacity and date.
Installation Requirements : R001 R130 R270

Note:
Proviso:
Manufacturer: Dewey Waters & Co Ltd
List all fittings by this manufacturer
Factor:
List all fittings by this factor
Listing Number 0310113

Print this entry
`Long-Life` range of one-piece rectangular GRP cold-water storage cisterns with bolt-on covers. Cisterns above 1m in depth have external steel support frames.
Size: 18.2 litres to 4500 litres.
Product Designation: Long-Life.
Marking: Adhesive label states model, capacity, manufacturer's name and address.
Installation Requirements : R001

Note:
Proviso:
Manufacturer: Nicholson Plastics Ltd
List all fittings by this manufacturer
Factor:
List all fittings by this factor
Listing Number 0609086

Print this entry
Circular sectional cistern for storing water for wholesome purposes. The cistern is manufactured of glass enamelled steel panels with external reinforcing rings bolted from the inside out, using galvanised bolts with polyethylene coated heads. The cistern is sealed internally using Sikaflex TS plus.
Size: 280,000 litres, 6.86m diameter, 8.65m high.
Product Designation: Tank number 3705D.
Marking: Manufacturer's name, volume, size of cistern and installers details printed on adhesive label on cistern adjacent to opening hatch on top of cistern.
Installation Requirements : R001 R270 R280 R350

Note:
Proviso:
Manufacturer: Vitkovice - Envi AS
List all fittings by this manufacturer
Factor:

WRAS Approved Water Fittings

WRAS Approved Water Fittings

Section 0120
Cisterns Storing Water for Domestic Purposes

DRINKING, WASHING, COOKING AND SANITARY
Cisterns in this section comprise units which include all the essential items identified in Schedule 2. Section 7, Paragraph 4. of the Water Supply (Water Fittings) Regulations 1999.

A.C. Plastic Industries Limited
Listing Number 0605131

`Aquastow` range of GRP sectional, cold water storage cisterns and covers. Units are constructed of panels (1m x 1m or 0.5m x 1m) manufactured from hot press moulded GRP, corner sections and stainless steel bracing. Roof covers are constructed from panels of the same manufacture and are provided with a manhole cover. Joints are sealed with Butyl sealant and secured with galvanised or stainless steel bolts. Cisterns are fitted with screened air inlets, screened warning and overflow pipes (can be supplied with an `AB` air gap).
Size: 228,000 litres.
Product Designation: `Aquastow` hot press moulded sectional GRP cold water storage tanks.
Marking: Aquastow, AC Plastics Industries Ltd, capacity, printed on adhesive label attached to outer panel.
Installation Requirements : R001,R270,R280,R350

Balmoral Group Ltd

Listing Number 0706067

`Balmoral M100-B30` range of hot press moulded GRP sectional, pre-insulated panels, for the construction of cold-water storage cisterns. Assembled panels are sealed with extruded butyl rubber. The cisterns are fitted with uPVC roof struts to support the roof panels. Galvanised steel struts internally brace them with stainless steel ties externally. The cisterns are provided with wholesome water storage kit consisting of a screened air inlet screened warning pipe and a screened overflow (where applicable). The roof structure is fitted with one or more sealed manhole access points, mounted either directly on the roof structure or fitted into a float operated valve housing. Nuts and bolts in contact with water are stainless steel.
Size: 1000 - 448,000 litres capacity.
Product Designation: Balmoral M100-B30.
Marking: Balmoral Tank, logo and contact information moulded into panels. Balmoral Tank, logo, date of manufacture and capacity printed on adhesive label attached to panel.
Installation Requirements :

R001

R270

R280

Balmoral Tanks
Listing Number 0605132

Range of rotationally moulded high-density polyethylene storage tanks. The polyethylene cisterns are fitted with tight fitting lids, screened air inlets, screened warning pipes and overflow. Can be supplied without fittings and fixtures.
Size:
Product Designation: LP1250WST, H3500WST, V1365WST, V1800WST, V2600WST, V3635WST, V5455WST, V7270WST and V10000WST.C1365, C1800, C2600, C3635, C5455, C7270, C10000, C15000, C20000, C25000, C30000, C35000, CH1500, CH2000, CH3500, CLP1250, CSL1000, CSL1250.
Marking: Balmoral tanks installation guide and product information printed on adhesive label attached to outer panel.
Installation Requirements : R001 R270 R280 R350

Decca Plastics Ltd

Listing Number 0503111

`Decca One Piece` range of GRP one-piece cold water storage cisterns and covers. Tanks are manufactured from glass-reinforced plastic and covers are sealed with WRAS approved polyethylene/butyl seal. The cisterns are supplied with screened air inlet connecting kits and above 1000 litres an inspection hatch is provided. They are supplied either un-insulated or pre-insulated. For a full product range see manufacturer`s catalogue.
Size: DP10-DP26, M1-M16, CM01-CM24, TP10-TP26.
Product Designation: Decca One Piece, Decca Two Piece.
Marking: Adhesive label with Decca Plastics, address, model and trade name and certification number.
Installation Requirements : R001 R270 R280

Dewey Waters & Co Ltd

Listing Number 0507099

Range of one-piece GRP cisterns and lids for domestic cold-water storage. Units can be pre- insulated with polyurethane foam and are supplied with a wholesome water kit consisting screened air inlet, screened warning pipe and close fitting vent pipe grommet. Cisterns above 200 litres are fitted with an inspection hatch. Capacity range 30L - 4500L.
Size: 30 litres - 4500 litres.
Product Designation: A, B, C, D, E, F, G and H ranges.
Marking: Adhesive label with Dewey Waters, capacity and date.
Installation Requirements : R001 R130 R270

Dewey Waters & Co Ltd

Listing Number 0507097

Print this entry
Range of GRP sectional, cold water storage cisterns and covers. Units are constructed of panels (0.5m x 0.5m, 1m x 0.5m, 1m x 1m or 4ft x 4ft, 4ft x 2ft, 2ft x 2ft) from contact moulded GRP, flanged internally and externally which are supported by stainless steel ties. Panels can be pre-insulated with polyurethane foam or standard non-insulated manufacture, which if required can be cased and insulated. Roof panels are constructed from panels and provided with an inspection hatch. Joints are sealed with butyl rubber sealant strip and secured with stainless steel bolts (integral) and galvanised (external). Also supplied with internal stainless steel ladder.
Size: Maximum height 4m. Capacity 500 – 450,000 litres.
Product Designation:
Marking: Adhesive label with Dewey Waters, capacity and date.
Installation Requirements : R001 R130 R270 R350

Dewey Waters & Co Ltd

Listing Number 0507096

Range of GRP sectional, cold water storage cisterns and covers. Storage for domestic purposes. Units are constructed of flanged panels (½m x ½m, 1m x ½m, 1m x 1m or 4ft x 4ft, 4ft x 2ft, 2ft x 2ft) from contact moulded GRP. Larger sizes with stainless steel ties. Panels can be supplied pre-insulated with polyurethane foam. Roof covers are constructed from panels of the same manufacture and are provided with an inspection hatch. Joints are sealed with butyl rubber sealant strip and secured with stainless steel bolts (internal) and galvanised (external). Cisterns are supplied with screened air inlets, screened warning and overflow pipes, and can be supplied with internal stainless steel ladder.
Size: 500 litres - 450,000 litres.
Product Designation:
Marking: Adhesive label with Dewey Waters, capacity and date.
Installation Requirements : R001 R130 R270 R350

Franklin Hodge Industries Ltd

Listing Number 0404067

`Liquistore` range of cylindrical sectional cisterns for the storage of potable water comprising a tank shell of aluminium or galvanised steel sheets braided with rolled angle and wind girders of aluminium or galvanised mild steel and with aluminium tank roof. The tank shell is lined with a butyl rubber liner where in contact with potable water. Nuts and bolts in contact with potable water are stainless steel. Structures in contact with potable water are painted with Intex P1106 or B1106/SL. The cistern is fitted with screened overflow and warning pipes where appropriate and screened air vents (McAlpine ZWC FBR).
Size: Maximum height 6.072m, 133000 litres.
Product Designation: Liquistore.
Marking: Metal label on tank stating company name, logo, date of manufacture and capacity.
Installation Requirements : R001 R270 R280 R330 R350

Harton Services Ltd

Listing Number 0612077

Range of underground cisterns and pump systems. The system incorporates a cold-water storage cistern with pump supply to the receiving building, which is encased within a GRP pod. The pod is designed with overflow and leakage sump (which discharges at high level), frost protection heater, automatic pump control panel, watertight cover with access hatching and vent pipe to atmosphere. The overflow and leakage sump is designed to receive water from both the overflow and any leakage of water from outside of the pod. Once the sump pump has been activated the indication on the control panel operates the electrically controlled valve on the mains supply to the storage cistern, a maintenance engineer must then be called to re- set the system. The indicating control panel is situated both within the pod and within the supply building and can also be connected to remote alarms. The inlet supply to the storage cistern incorporates a non-verifiable double check assembly.
Size: 250 litres to 7500 litres.
Product Designation: Pod 7500, Pod 5000, Pod 2600.Minipod 1100.Micropod 1300, Micropod 800, Micropod 500, Micropod 250.
Marking: Manufacturer's name, contact details, serial number and installation instructions printed on adhesive label attached to control room wall.
Installation Requirements : R001

Note:
Proviso: 1. The air vent pipe and sump pump discharge pipe shall discharge above the flood height of the area where the pod is installed. 2. The air vent and sump pump discharge shall be protected against physical damage. 3. There must be a service and maintenance contract for the pod at all times. 4. All supply pipes to and from the pod shall be at a depth of between more than 750mm to 1350mm.
Manufacturer: Harton Services Ltd

IES - Robust Tanks Ltd

Listing Number 0302059

Range of one-piece GRP cisterns and lids for the storage of wholesome cold water. Units are pre-insulated with 25mm rigid polyurethane foam and polyester gel coating. Cisterns are fitted with a cover (secured with bolts), screened air inlet and screened overflow assembly.
Size: 125 litres - 9000 litres.
Product Designation: `Robust` imperial and metric range.
Marking: Adhesive label printed with manufacturer`s details, size/volume and reference number.
Installation Requirements : R001 R130 R270 R280

Parton Fibreglass Ltd
Listing Number 0507095

PFG range of rectangular cisterns. The glass reinforced plastic pre-insulated cisterns are fitted with a cover (secured with bolts), screened air inlet, screened warning pipe and close fitting expansion pipe inlet. Size & Product Designation: Imperial range P1 (68 litres) to P19 (4545 litres). Metric range P501 (90 litres) to P511 (2600 litres). Low Profile range P203 (170 litres) to P219 (2050 litres).
Size:
Product Designation:
Marking: PFG labelled with Ref No and capacity printed on cistern.
Installation Requirements : R001 R130 R270

Note:
Proviso:
Manufacturer: Parton Fibreglass Ltd

Parton Fibreglass Ltd
Listing Number 0209087

`PFG` range of sectional, cold water storage cisterns and covers. Units are constructed of panels (1m x 1m or 0.5m x 1m) from hot press mouldings GRP. Corner sections, roof panels and access holes are constructed of the same material. The cisterns have stainless steel internal bracing and galvanised external bracing. Joints are sealed with EPDM rubber or polyethylene foam. Cisterns are fitted with screened air inlets, screened warning and overflow pipes. Supplied with an internal GRP composite access ladders.
Size: Maximum height of unit 4.0m. Panel sizes 1m x 1m, 1m x 1/2m, 1/2m x 1/2m.
Product Designation: PFG range.
Marking: Manufacturer's name, address, capacity.
Installation Requirements : R001 R130 R270 R280 R350

Note:
Proviso:
Manufacturer: Parton Fibreglass Ltd

Polytank Ltd
Listing Number 0410034

`Polytank` range of kite marked black polyethylene feed and expansion cisterns to BS4213: 2004 for storing water for domestic purposes. Packed with all fittings to meet the requirements of Water Supply (Water Fittings) Regulations 1999. Fittings include snap on lid, insulation, screened air inlet, screened warning pipe elbow including tank connector, dip tube, expansion pipe grommet, back plate, plastic support washer and rubber sealing washer.
Size: 4 gallons (18 litres) to 100 gallons (454 litres).
Product Designation: Polytank PC4R 18 x 12 x 12 Polytank PC12R 20 x 12 x 20 Polytank PC12R 24 x 16 x 15 Polytank PC12R 20 x 15 x 18 Polytank PC15R 18 x 18 x 18 Polytank PC15R 24 x 12 x 20 Polytank PC15R 24 x 17 x 17 Polytank PC15R 24 x 15 x 18 Polytank PC18R 24 x 12 x 24 Polytank PC18R 24 x 18 x 19 Polytank PC20R 20 x 20 x 20 Polytank PC20R 24 x 15 x 24 Polytank PC25R 27 x 20 x 20 Polytank PC30R 24 x 24 x 24 Polytank PC35R 29 x 22 x 22 Polytank PC35R 30 x 24 x 23 Polytank PC42R 39 x 20 x 21 Polytank PC42R 46 x 19 x 19 Polytank PC50R 36 x 24 x 23 Polytank PC50R 46 x 24 x 19 Polytank PC25R 55 x 20 x 12 Polytank PC50R 64 x 18 x 19 Polytank PC70R 64 x 24 x 19 Polytank PC100R 64 x 26 x 23 Circular PC25C C25 Circular PC50C C50 Slimtank PC15X 30 x 19 x 15 Slimtank PC25X 30 x 19 x 19 Slimtank PC40X 46 x 24 x 17 Slimtank PC50X 46 x 24 x 20 XX size of tank in gallons. PC4R = 4 gallons.
Marking: `Polytank` embossed in body.
Installation Requirements : R001

Note:
Proviso:
Manufacturer: Polytank Ltd

POW Processes of Water Ltd

Listing Number 0210076

`S` and `D` range of pre-insulated one-piece GRP cisterns with lids, for cold-water use only. The tanks are strengthened externally with GRP coated bored prime steel frames running horizontally around the tank. The tanks have one-piece lids below 1000 litres and above are fitted with manhole access.
Size: 340 litres - 9700 litres.
Product Designation: S1 to S34, D1 to D34.
Marking: Adhesive label stating POW and type.
Installation Requirements : R001

Note:
Proviso:
Manufacturer: POW Processes of Water Ltd

POW Processes of Water Ltd
Listing Number 0606087

Metric and imperial ranges of GRP sectional cold-water storage cisterns, constructed from sectional panels, metric (1.5m x 1.0m) (1.0m x 1.0m) (1.0m x 0.5m) or imperial sizes (4ft x 4ft) (4ft x 2ft) (2ft x 2ft). Joints are sealed using plasticised butyl rubber. Having stainless steel tie rods and pultruded GRP inspection ladders.
Size: 1000 ltrs to 53625 ltrs.
Product Designation: `Metric` range `Imperial` range.
Marking: Laminated adhesive label printed with manufacturers name, address, telephone number, product code and capacity.
Installation Requirements : R001 R270 R280

Note:
Proviso:
Manufacturer: POW Processes of Water Ltd

Purewater Storage Ltd
Listing Number 0209086

`PW` range of pre-insulated rectangular one piece glass reinforced plastic cisterns for storing water for domestic purposes, having crystic resin and gel coat, having a one piece lid (GRP) all joints are sealed using polyethylene foam and having a square inspection hatch. Supplied with a potable water kit (McAlpine & Co Ltd). For cold water storage only.
Size: 90 - 9000 litres.
Product Designation: PW90 nominal capacity 90 litres PW160 nominal capacity 160 litres PW225 nominal capacity 225 litres PW340 nominal capacity 340 litres PW454 nominal capacity 454 litres PW570 nominal capacity 570 litres PW680 nominal capacity 680 litres PW909 nominal capacity 909 litres PW1135 nominal capacity 1135 litres PW1364 nominal capacity 1364 litres PW1590 nominal capacity 1590 litres PW1818 nominal capacity 1818 litres PW2272 nominal capacity 2272 litres PW2726 nominal capacity 2726 litres PW2850 nominal capacity 2850 litres PW3636 nominal capacity 3636 litres PW4535 nominal capacity 4535 litres PW5440 nominal capacity 5440 litres PW125 nominal capacity 125 litres PW250 nominal capacity 250 litres PW500 nominal capacity 500 litres PW750 nominal capacity 750 litres PW1000 nominal capacity 1000 litres PW1500 nominal capacity 1500 litres PW2000 nominal capacity 2000 litres PW2500 nominal capacity 2500 litres PW3000 nominal capacity 3000 litres PW3750 nominal capacity 3750 litres PW4500 nominal capacity 4500 litres PW5000 nominal capacity 5000 litres PW6000 nominal capacity 6000 litres PW7500 nominal capacity 7500 litres PW9000 nominal capacity 9000 litres
Marking: Side of cistern with an adhesive label showing manufacturer's name and address, product code, nominal capacity.
Installation Requirements : R001 R130 R270 R350

Note:
Proviso:
Manufacturer: Purewater Storage Ltd

Sarena MFG Ltd

Listing Number 0606090

SC, M, EN, Low and GRP horizontal split ranges of rectangular glass reinforced polyester (GRP) cold-water storage cisterns and lids. Joints of the split tanks are sealed with mastic sealing tape and secured with stainless steel fixings. Units can be factory pre-insulated (with provision for the fixture of fittings) or non-insulated and supplied with insulating jackets to protect from heat and frost. Supplied with screened vent, screened overflow, grommet pipe fitting and screened warning pipes. Float operated valves are available as an option (Keraflo Aylesbury Valves).
Size: SC maximum capacity 4540 (litres) 1000 (gallons). M maximum capacity 6810 (litres) 1500 (gallons). EN maximum capacity 8000 (litres) 1760 (gallons). Low maximum capacity 3451 (litres) 760 (gallons). GRP horizontal split maximum capacity 8000 (litres) 1760 (gallons).
Product Designation: SC, M, EN, Low and GRP horizontal split ranges.
Marking: Pre-insulated `Sarena` tanks printed on outer panel. Manufacturer's name, address, model number, capacity, installation and warranty instructions printed on adhesive label.
Installation Requirements : R001 R270 R280

Note:
Proviso:
Manufacturer: Sarena MFG Ltd

Sarena MFG Ltd

Listing Number 0606089

One piece, horizontal split and vertical split ranges of glass reinforced polyester (GRP) cold-water storage cisterns and lids of non-stock sizes (special pattern). Joints of the split tanks are sealed with mastic sealing tape and secured with stainless steel fixings. Units can be factory pre-insulated (with provision for the fixture of fittings) or non-insulated and supplied with insulating jackets to protect from heat and frost. Supplied with screened vent, screened overflow, grommet pipe fitting and screened warning pipes. Float operated valves are available as an option (Keraflo Aylesbury Valves).
Size: One piece maximum capacity 8000 litres, horizontal split maximum vertically split maximum capacity 4000 litres, capacity 8000 litres.
Product Designation: SP one piece and horizontal split VST vertically split.
Marking: Pre-insulated `Sarena` tanks printed on outer panel. Manufacturer's name, address, model number, capacity, installation and warranty instructions printed on adhesive label.
Installation Requirements : R001 R270 R280

Note:
Proviso:
Manufacturer: Sarena MFG Ltd

WRAS Approved Materials:(GRP) Section5125 Material Only

WRAS Approved Materials

Glass Reinforced Plastics (GRP)
Section 5125 MATERIAL ONLY

Components made from materials listed in this section may be required to be submitted for audit tests.
Listing Number 0705512

Binani. Hot press moulded GRP sheet panels. Cold water use only.
Supplier: BT Composites Ltd
Listing Number 0707507

Verplen C30 04 NE ACLUV black, Verplen C30 01 NE ACLKUV black and Verplen C30 08 NT ACLKUV natural. Glass fibre filled PP. For cold wate and hot water use up to 60°C.
Supplier: Ravago Italia Spa
Listing Number 0708502

KPR 6770 Terephthalic Polyester Resin. For cold water and hot water use up to 50°C.
Supplier: Kemrock Industries and Exports Ltd
Listing Number 0705515

GR103/5 SMC. Moulded, cream coloured GRP material. Cold water use only.
Supplier: Gloucester Composites Limited
Listing Number 0210518

AC - pale green GRP. For cold water and hot water use up to 50°C only.
Supplier: Advanced Composites FZC
Listing Number 0508527

GRP pipe and fittings. For cold water and hot water use up to 50°C.
Supplier: Amiantit Fiberglass Ind Ltd (AFIL)
Listing Number 0606515

Bushepol 751129. Translucent beige coloured unsaturated polyester resin. For cold water and hot water use up to 55°C.
Supplier: Bushehr Chemical Industries Co
Listing Number 0404519

IB 10029A Isopl Brush Gelcoat. Grey coloured unsaturated polyester resin. For cold water and hot water use up to 40°C.
Supplier: Colorplas Ltd
Listing Number 0304515

Encore 2020, Encore 2030 and Endyne E9113. White coloured gel coated glass reinforced unsaturated polyester laminatiing resins. Cold water use only.
Supplier: Cray Valley Ltd
Listing Number 0507510

Polycor gel coat. Spray or brush applied. May be used with the following laminating resins. Quickcure 2 - Quickcure 3 - Quickcure 13 - Quickcure 20 - Quickcure 30. Quickcure 2L - Quickcure 3L - Quickcure 13L - Quickcure 20L - Quickcure 30L - Quickcure 30L grey pigmented. Encore 2 - Encore 13 - Encore 20 - Encore 30 - Encore 40. Endyne 20, Endyne 30 and Norsodyne 6397.111. Cold water use only.
Supplier: Cray Valley Ltd
Listing Number 0309504

Atlac 590. Straw coloured translucent GRP material. For cold water and hot water use up to 45°C.
Supplier: DSM Composite Resins UK Ltd
Listing Number 0309503

Atlac 580. Straw coloured translucent GRP material. For cold water and hot water use up to 45°C.
Supplier: DSM Composite Resins UK Ltd
Listing Number 0505511

Neogel 6000-I-1. Translucent beige GRP. Cold water use only.
Supplier: DSM Composite Resins UK Ltd
Listing Number 0402505

Neogel 2000-I-1. Translucent beige gelcoat backed up with Synolite 2020-P-1 GRP. Cold water use only.
Supplier: DSM Composite Resins UK Ltd
Listing Number 0404502

Synolite 8210-P-1. Translucent beige coloured GRP. Cold water use only.
Supplier: DSM Composite Resins UK Ltd
Listing Number 0410506

Synolite 2020-P-1. Translucent beige coloured and 2020-W-1 white coloured unsaturated polyester resin. Cold water use only.
Supplier: DSM Composite Resins UK Ltd
Listing Number 0410507

Synolite 6440-N-1. Translucent beige coloured unsaturated polyester resin. Cold water use only.
Supplier: DSM Composite Resins UK Ltd
Listing Number 0410505

Synolite 6060-P-1. Translucent beige coloured unsatureated polyester resin. Cold water use only.
Supplier: DSM Composite Resins UK Ltd
Listing Number 0410501

Farapipe based on Crystic 274 polyester. Grey/green coloured GRP material. Cold water use only.
Supplier: Farassan Manufacturing & Industrial Company
Listing Number 0704505

Atlac 430. Vinyle ester resin. Clear coated GRP panel. For cold water and hot water use up to 60°C.
Supplier: Jinling DSM Resin Company Ltd
Listing Number 0409523

HUP 16. Grey coloured glass fibre reinforced thermoset SMC compression moulding. For cold water use up to 40°C.
Supplier: Lonza Compounds GmbH & Co KG
Listing Number 0601521

Flomat 47-3007. Grey coloured GRP material. For use as a water tank panel. Cold water use only.
Supplier: Menzolit Ltd
Listing Number 0702517

SMC 200. Hot press/steel moulded sheet compound. For cold water and hot water use up to 40°C.
Supplier: NIPCO
Listing Number 0211509

Estaloc T5160 nat 030. Translucent straw coloured material. Cold water use only. This material is translucent and therefore not suitable for use in fittings where it may be exposed to light.
Supplier: Noveon Europe bvba
Listing Number 0303502

PV4 & PV5. Translucent green glass fibre reinforced epoxy resin. Cold water use only.
Supplier: Phoenix Vessels Ltd
Listing Number 0209510

Crystic 474PA. Semi-opaque with pink/grey tinge, unsaturated polyester laminating resin. Cold water use only.
Supplier: Scott Bader Co Ltd
Listing Number 0607502

Crystic Gelcoat 65PA/Crystic 2-406PA laminating resin. Cure 3 hours at 80°C. Cold water use only.
Supplier: Scott Bader Co Ltd
Listing Number 0301503

Envirotec Gelcoat LS88PA & LS98PA. Semi-opaque, straw coloured polyester resin. For use up to a maximum temperature of 40°C.
Supplier: Scott Bader Co Ltd
Listing Number 0508524

Vetroresina GRP material. For cold water use only.
Supplier: Vetroresina Enginia Spa
Listing Number 0210507

Yeung`s opaque beige panel with white polyester resin and polyester resin gelcoat. Cold water use only.
Supplier: Yeungs Fiberglass Company
Listing Number 0507509

SMC penal for HiTank. Grey coloured panel water tank. For cold water and hot water use up to 50°C.
Supplier: Young Sung Industrial Co Ltd
Listing Number 0404520

SMC panel grade W/01. Cream coloured GRP sheet moulding compound. For cold water and hot water use up to 40°C.
Supplier: Zhenjiang Yangtze Tank Manufacturing Co Ltd

WRAS Approved Materials:Glass Reinforced Plastics(GRP)

WRAS Approved Materials

Glass Reinforced Plastics (GRP)
Section 5120 COMPONENTS

Listing Number 0703520

Flosto GRP SMC 523/35. Hot press moulded light grey coloured tank panel. Cold water use only.
Supplier: Devi Polymers Private Ltd
Listing Number 0509523

Glass reinforced vinylester olive coloured pipe. For use in contact with water up to 40°C.
Supplier: Abu Dhabi Pipe Factory
Listing Number 0502508

ADPF - GRP. Translucent light green glass reinforced polyester pipe with Isophthalic resin. For cold water and hot water use up to 40°C.
Supplier: Abu Dhabi Pipe Factory
Listing Number 0502507

ADPF - GRE. Translucent light green glass reinforced epoxy pipe For cold water and hot water use up to 40°C.
Supplier: Abu Dhabi Pipe Factory
Listing Number 0608511

GRE pipe 008M24405. Translucent green coloured pipe. Cold water and hot water use up to 60°C.
Supplier: Advanced Composites FZC
Listing Number 0508531

GRP pipe and fittings. For cold water and hot water use up to 50°C.
Supplier: Amitech Saudi Arabian for Fibreglass Co (Amitech)
Listing Number 0603516

Anabeeb GRP potable water pipe. For cold water and hot water use up to 50°C.
Supplier: Anabeeb Pipes Manufacturing Factories
Listing Number 0609518

Anchor-Link (*). Grey coloured and Ivory coloured SMC moulded GRP tank panel. For cold water and hot water use up to 50°C.
Supplier: Anchor Link SDN BHD
Listing Number 0305510

GRP grey coloured ladder section. Cold water use only.
Supplier: Chemglass Ltd
Listing Number 0505508

CPI-PS. Pale yellow coloured GRP pipe. For cold water and hot water use up to 60°C.
Supplier: Composite Pipes Industry LLC
Listing Number 0301529

Unipanel. Grey coloured GRP (SMC) hot press moulded tank panels. Cold water use only.
Supplier: Decca Plastics Ltd
Listing Number 0301524

Flosto. Grey coloured GRP (SMC) hot press moulded panel tanks. Cold water use only.
Supplier: Devi Polymers Private Ltd
Listing Number 0405515

DPFC-GRP. Off-white/grey and beige coloure pipe and fittings. For cold water and hot water use up to 50°C.
Supplier: Dubai Pipes Factory Co LLC
Listing Number 0608518

Extralite HL/DWF-15-06. GRP beige pipe fitting. For cold water and hot water use up to 50°C.
Supplier: Extra Co Fibre Glass & Prefab Houses LLC
Listing Number 0608519

Extralite FW/DWP-200-15-06. GRPgreen pipe. For cold water and hot water use up to 50°C.
Supplier: Extra Co Fibre Glass & Prefab Houses LLC
Listing Number 0606501

Farapol ortho polyester. Translucent beige GRP pipe. For cold water and hot water use up to 50°C.
Supplier: Fara Paye Zhad Chemical Industries
Listing Number 0512508

Farapol 101. Off white coloured GRP pipe. For cold water and hot water use up to 40°C.
Supplier: Farassan
Listing Number 0410502

Farapipe based on Farapol 101 polyester. Off-white coloured pipe. Cold water use only.
Supplier: Farassan Manufacturing & Industrial Company
Listing Number 0502512

Force 800. Grey coloured pultruded glass reinforced polyester resin profiles. Cold water use only.
Supplier: Fibreforce Composites Ltd
Listing Number 0307523

GRP-FPI(E) - Fiberstrong. Beige translucent coloured pipe. Cold water and hot water use up to 50°C.
Supplier: Future Pipe Industries (SAE)
Listing Number 0310511

GRE-FPI(E) - Wavistrong. Yellow translucent coloured glass reinforced epoxy pipe. Cold water and hot water use up to 85°C.
Supplier: Future Pipe Industries (SAE)
Listing Number 0406523

Wavistrong Series ES. Yellow coloured glass fibre reinforced epoxy pipe system. Helical wound glass fibres impregnated in thermosetting amine cured epoxy resin. Cold water use only.
Supplier: Future Pipe Industries BV
Listing Number 0210508

GRE-FPI-Wavistrong. Translucent yellowish GRP pipe. For cold water and hot water use up to 85°C. This product is translucent and therefore not suitable for use in fittings where it may be exposed to light.
Supplier: Future Pipe Industries LLC
Listing Number 0308502

GRP-FPI-KSA Fiberstrong. Beige coloured GRP pipe. For cold water and hot water use up to 50°C.
Supplier: Future Pipe Industries LLC-KSA
Listing Number 0209513

PW-GEI-EEII. GRE translucent natural pipe. For cold water and hot water use up to 85°C. This product is translucent and therefore not suitable for use in fittings where it may be exposed to light.
Supplier: Gulf Eternit Industries Co Ltd
Listing Number 0409528

Hepworth PME. Honey coloured GRP pipe and fittings. For cold water and hot water use up to 50°C.
Supplier: Hepworth PME
Listing Number 0502516

Atlac 580. Translucent beige GRP with vinylester resin. For cold water and hot water use up to 60°C.
Supplier: Iniziative Industriali Spa
Listing Number 0609503

NIKKO. Cream coloured FRP water tank panel. For cold water and hot water use up to 50°C.
Supplier: New Trade Links Ltd
Listing Number 0608506

NP501A (Nema FR-4). Translucent natural coloured GRE isolation sealing gasket. For cold water and hot water use up to 50°C.
Supplier: Pikotek
Listing Number 0609513

Bondstrand 3400/2000G. Brown coloured GRE pipe. Cold water use only.
Supplier: PPG Industries Netherlands BV
Listing Number 0303522

GRP pipe and fittings. Yellow coloured GRP. For potable cold water and hot water use up to 50°C.
Supplier: Superlit Boru Ve Levha San A.S